€
€ essentials
UDOO GROVE STARTER KIT
€60.35
With this Kit you'll have all the Sensors you want to develop and realize all your ideas.
CASE FOR NEO
€7.50
The plastic case for your UDOO NEO board.
LIGHT SENSOR KIT
€6.50
Use this Light Sensor Brick to augment your UDOO boards and make them more versatile.
POWER SUPPLY 12V 3A EU
€10.95
Not available
AC Power Supply Adapter DC 12 Volt 3 Amp
POWER SUPPLY 12V 3A USA
€10.95
Not available
AC Power Supply Adapter DC 12 Volt 3 Amp
must-haves
7INCH HDMI/USB DISPLAY/TOUCH
€81.50
The wonderful 7inch HDMI/USB Display/Touch with 1024×600 high resolution.
USB KIT
€4.80
Not available
This Kit contain a Micro USB to USB OTG Host Adapter + Micro-USB to USB Cable (50cm)
USB/SERIAL DEBUG MODULE FOR NEO
€3.00
The USB/Serial debug module you can use only with your UDOO NEO
cables
MICRO HDMI TO HDMI CABLE
€4.15
The Micro HDMI to HDMI cable for NEO.
sensors
BAROMETER ALTIMETER TEMPERATURE KIT
€4.50
Use this Barometric/Altimeter/Temperature Sensor Brick to augment your UDOO boards and make them more versatile.
TEMPERATURE SENSOR KIT
€3.90
Use this Temperature Sensor Brick to augment your UDOO boards and make them more versatile.
HUMIDITY SENSOR KIT
€9.60
Not available
Use this Humidity Sensor Brick to augment your UDOO boards and make them more versatile.
GESTURE SENSOR KIT
€15.00
Use this Gesture Sensor Brick to augment your UDOO boards and make them more versatile.
UDOO NEO FULL
€77.00
UDOO NEO FULL
Usually ships in 2-4 days
Not available
€77.00
excl. TAX/VAT/SHIPPING
| CPU | NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core. Cortex-M4 Core |
|---|---|
| Graphics | Vivante GC420 Integrated 2D/3D graphics accelerator |
| Connectivity | MicroSD card slot onboard. 8-bit SDIO interface |
| Memory | RAM 1GB |
UDOO NEO FULL
| Processor | NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core and a Cortex-M4 Core |
|---|---|
| Memory | RAM 1GB |
| Graphics | Vivante GC420 Integrated 2D/3D graphics accelerator |
| Video Interfaces | Micro HDMI interface - LVDS interface + touch (I2C signals) Analog camera connection supporting NTSC and PAL 8-bit parallel camera interface* |
| Mass Storage | MicroSD card slot onboard 8-bit SDIO interface* |
| Networking | Fast ethernet RJ45 – 10/100Mbps Wi-Fi 802.11 b/g/n,Direct Mode SmartConfig and Bluetooth 4.0 Low Energy |
| Usb | 1x USB 2.0 Type A ports 1x USB OTG (micro-AB connector) |
| Audio | HDMI audio transmitter S/PIDF & I2S* |
| Serial Ports | 3x UART ports* 2x CAN Bus interfaces* |
| Other Interfaces | 8x PWM signals* 3x I2C interface* 1x SPI interface* 6x multiplexable signals* |
| Leds | 1x Green Power Status LED 2x User Configurable LEDs (Red and Orange) |
| Integrated Sensors | 3-Axis Accelerometer 3-Axis Magnetometer 3-Axis Digital Gyroscope 1x Sensors Snap-in I2C connector |
| Power Supply | 1x DC Micro USB 5V 1x DC Power Jack 6-15V 1x RTC Battery Connector |
| Operating System | Linux UDOObuntu2 (14.04 LTS) Android Marshmallow 6.0.1 |
| Dimensions | 89mm x 59mm - 3.50 inch x 2.32 inch |
| Arduino Pinout | Arduino-compatible through the standard Arduino Uno layout and compatible with Arduino shields. |
| Digital Pins | 32 extended GPIOs (A9 dedicated) 22 Arduino GPIOs (M4 dedicated) |
| Analog Pins | 6 available Pins |
| Campo Note | *Available on Pin Header |
View all specs
View less specs
| Processor | NXP™ i.MX 6SoloX applications processor with an embedded ARM Cortex-A9 core and a Cortex-M4 Core |
|---|---|
| Memory | RAM 1GB |
| Graphics | Vivante GC420 Integrated 2D/3D graphics accelerator |
| Video Interfaces | Micro HDMI interface - LVDS interface + touch (I2C signals) Analog camera connection supporting NTSC and PAL 8-bit parallel camera interface* |
| Mass Storage | MicroSD card slot onboard 8-bit SDIO interface* |
| Networking | Fast ethernet RJ45 – 10/100Mbps Wi-Fi 802.11 b/g/n,Direct Mode SmartConfig and Bluetooth 4.0 Low Energy |
| Usb | 1x USB 2.0 Type A ports 1x USB OTG (micro-AB connector) |
| Audio | HDMI audio transmitter S/PIDF & I2S* |
| Serial Ports | 3x UART ports* 2x CAN Bus interfaces* |
| Other Interfaces | 8x PWM signals* 3x I2C interface* 1x SPI interface* 6x multiplexable signals* |
| Leds | 1x Green Power Status LED 2x User Configurable LEDs (Red and Orange) |
| Integrated Sensors | 3-Axis Accelerometer 3-Axis Magnetometer 3-Axis Digital Gyroscope 1x Sensors Snap-in I2C connector |
| Power Supply | 1x DC Micro USB 5V 1x DC Power Jack 6-15V 1x RTC Battery Connector |
| Operating System | Linux UDOObuntu2 (14.04 LTS) Android Marshmallow 6.0.1 |
| Dimensions | 89mm x 59mm - 3.50 inch x 2.32 inch |
| Arduino Pinout | Arduino-compatible through the standard Arduino Uno layout and compatible with Arduino shields. |
| Digital Pins | 32 extended GPIOs (A9 dedicated) 22 Arduino GPIOs (M4 dedicated) |
| Analog Pins | 6 available Pins |
| Campo Note | *Available on Pin Header |
View all specs
View less specs
The most complete tool for wireless mobile IoT applications.
UDOO NEO FULL is the best, all-in-one solution for wireless mobile IoT applications.
You can use it as a Headless Device, exploiting the USB and Ethernet ports and the Wireless Connectivity - a powerful Wi-Fi b/g/n and the newest BT 4.0. You can also use it as a computer, thanks to its 1GB of RAM.
The board is compatible with most Arduino shields, sensors and actuators. UDOO NEO FULL is also compatible with UDOO Bricks: programmable modules, like the temperature sensor and the barometric sensor, that you can add to make UDOO NEO FULL even more versatile.
UDOO NEO FULL can be powered in three ways. You can use:
- A standard 12 volts power supply, we recommend this one;
- A Micro USB cable like the one we have in our USB Kit;
- Any USB battery pack available on the market.
List of Components:
- 1x UDOO NEO FULL
You can check out our Kickstarter Campaign.
UDOO NEO FULL is the best, all-in-one solution for wireless mobile IoT applications.
You can use it as a Headless Device, exploiting the USB and Ethernet ports and the Wireless Connectivity - a powerful Wi-Fi b/g/n and the newest BT 4.0. You can also use it as a computer, thanks to its 1GB of RAM.
The board is compatible with most Arduino shields, sensors and actuators. UDOO NEO FULL is also compatible with UDOO Bricks: programmable modules, like the temperature sensor and the barometric sensor, that you can add to make UDOO NEO FULL even more versatile.
UDOO NEO FULL can be powered in three ways. You can use:
- A standard 12 volts power supply, we recommend this one;
- A Micro USB cable like the one we have in our USB Kit;
- Any USB battery pack available on the market.
List of Components:
- 1x UDOO NEO FULL
You can check out our Kickstarter Campaign.
Check items to add to the cart or
-
![CASE FOR NEO]()
CASE FOR NEO€7.50 excl. TAX/VAT/SHIPPING -
![USB/SERIAL DEBUG MODULE FOR NEO]()
USB/SERIAL DEBUG MODULE FOR NEOSpecial Price €3.00 Regular Price €9.00 excl. TAX/VAT/SHIPPING -
![POWER SUPPLY 12V 3A EU]()
POWER SUPPLY 12V 3A EU€10.95 excl. TAX/VAT/SHIPPING -
![POWER SUPPLY 12V 3A USA]()
POWER SUPPLY 12V 3A USA€10.95 excl. TAX/VAT/SHIPPING -
![UDOO GROVE STARTER KIT]()
UDOO GROVE STARTER KIT€60.35 excl. TAX/VAT/SHIPPING -
![7INCH HDMI/USB DISPLAY/TOUCH]()
7INCH HDMI/USB DISPLAY/TOUCH€81.50 excl. TAX/VAT/SHIPPING -
![MICRO HDMI TO HDMI CABLE]()
MICRO HDMI TO HDMI CABLESpecial Price €4.15 Regular Price €8.00 excl. TAX/VAT/SHIPPING -
![USB KIT]()
USB KIT€4.80 excl. TAX/VAT/SHIPPING -
![GESTURE SENSOR KIT]()
GESTURE SENSOR KITSpecial Price €15.00 Regular Price €19.00 excl. TAX/VAT/SHIPPING -
![HUMIDITY SENSOR KIT]()
HUMIDITY SENSOR KIT€9.60 excl. TAX/VAT/SHIPPING -
![TEMPERATURE SENSOR KIT]()
TEMPERATURE SENSOR KITSpecial Price €3.90 Regular Price €10.90 excl. TAX/VAT/SHIPPING -
![LIGHT SENSOR KIT]()
LIGHT SENSOR KITSpecial Price €6.50 Regular Price €10.50 excl. TAX/VAT/SHIPPING -
![BAROMETER ALTIMETER TEMPERATURE KIT]()
BAROMETER ALTIMETER TEMPERATURE KITSpecial Price €4.50 Regular Price €12.20 excl. TAX/VAT/SHIPPING
|
|
